Lifting Eyebolts
?* Information on days to ship and prices
-
DIN 580 Lifting eye bolts, Steel
GANTER
These lifting eye bolts correspond to standard sheet DIN 580.
The following guidelines of lifting eye bolts DIN 580 the have to be observed in addition to the load values given in the above table.
The eye bolt must be of fully screwd in to achieve a perfect contact between the two mating faces.
Both threads must be of a equal length and the base material of equal strength to that of the bolt.
Operating instructions with more details and specifications are included with every delivery (see also www.ganter-griff.com/service).
The official DIN standard sheet specifies the additional sizes M42, M48, M56, M64, M72 x 6, M80 x 6 und M100 x 6.- Volume Discount
› Configure nowStarting from∗ ： 2.48 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
› Configure now
Starting from∗ ： 0.81 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Lifting eye bolts (rotating), Steel
GANTER
The lifting eye bolts GN 581are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as potentially possible in lifting eye bolts DIN 580).
Lifting eye bolts GN 581 offer a high load carrying capacity and they are tested to meet safety standards (safety factor 4).
The rated load carrying capacity listed in the above table is clearly marked on the ring. It applies to the most unfavourable load application of the load types listed opposite.
Lifting eye bolts GN 581 comply with Mechanical Engineering Directive 2006 / 42 / EG and are BG tested.
The integrated RFID transponder clearly marks and identifies the sling and lifting gear, e.g. during the prescribed regular inspection.
The hexagon socket bolt cannot be removed from the ring.
Type B is suitable for assembly without the need to use tools: inserting the spanner in the hexagon socket of the bolt allows the bolt to be turned in and out by hand.- Volume Discount
- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 80.20 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Eye bolts DIN 444 Form B with long thread (K1418)
KIPP
· Suitable for use as hinge pins, swing hinges and guides
· Version: steel or stainless steel- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 3.16 € Min. Shipping Days ： 4 Days *Unit price with basic configuration
-
Lifting eye bolts, Stainless Steel A2
GANTER
The following guidelines for Stainless Steel-Lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table.
The eye bolt must be of fully screwed in to achieve a perfect contact between the two mating faces.
Both threads must be of a equal length and the base material of equal strength to that of the bolt.
Operating instructions with more details and specifications are included with every delivery (see also www.ganter-griff.com/service).
The official DIN standard sheet specifies the additional sizes M42, M48, M56, M64, M72 x 6, M80 x 6 und M100 x 6.- Volume Discount
› Configure nowStarting from∗ ： 5.18 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Ring bolts DIN 580 (K0767)
KIPP
· For hoisting and transport tasks
· Application sectors: machine and fixture construction, toolmaking, logistics, material handling
· Version: steel or stainless steel- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 1.25 € Min. Shipping Days ： 4 Days *Unit price with basic configuration
-
Eye bolts DIN 444 Form B (K0396)
KIPP
· Suitable for use as hinge pins, swing hinges and guides
· Version: steel or stainless steel- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 3.16 € Min. Shipping Days ： 4 Days *Unit price with basic configuration
-
Lifting eye bolts, Stainless Steel A4
GANTER
The following guidelines for Stainless Steel-Lifting eye bolts DIN 580 have to be observed in addition to the load values given in the above table.
The eye bolt must be of fully screwed in to achieve a perfect contact between the two mating faces.
Both threads must be of a equal length and the base material of equal strength to that of the bolt.
Operating instructions with more details and specifications are included with every delivery (see also www.ganter-griff.com/service).
The official DIN standard sheet specifies the additional sizes M42, M48, M56, M64, M72 x 6, M80 x 6 und M100 x 6.- Volume Discount
› Configure nowStarting from∗ ： 11.58 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Lifting Pin Self-Locking
HALDER
[Features]
· Corrosion resistant
· Heat resistant to 250°C
· Locating· Bushing use one from 22350.0900 to 0.0936 (for d1 = 8, 10, 12, 16).
· Fitting for hanging that is speedy and simple to use yet solid.
· The movable shackle is equipped with a safety bar to prevent the button from being pushed unintentionally.
· A tap hole is not required for the item to be hung, only a H11 hole is needed.- 3D CAD data available
› Configure nowStarting from∗ ： 67.17 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Lifting eye bolts (rotating), Stainless Steel
GANTER
Stainless Steel-Lifting eye bolts GN 581.5 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as potentially possible in Stainless Steel-Lifting eye bolts DIN 580).
Stainless Steel-Lifting eye bolts GN 581.5 offer a high load carrying capacity and they are tested to meet safety standards (safety factor 4).
The rated load carrying capacity listed in the above table is clearly marked on the ring. It applies to the most unfavourable load application of the load types listed opposite.
Stainless Steel-Lifting eye bolts GN 581.5 eye bolts comply with Mechanical Engineering Directive 2006 / 42 / EG and are BG tested.
The integrated RFID transponder clearly marks and identifies the sling and lifting gear, e.g. during the prescribed regular inspection.
The hexagon socket bolt cannot be removed from the ring.- Volume Discount
- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 176.26 € Min. Shipping Days ： 4 Days *Unit price with basic configuration
-
Threaded Lifting Pins, self-locking
HALDER
Heavy-duty lifting element for quick and easy use, with moveable shackle and locking stud to provide protection against unintentional unlocking. For lifting loads, the threaded lifting pin is inserted into a threaded hole. In contrast to a ringbolt, time-consuming screwing in and out is therefore unnecessary.
All versions are corrosion-protected. The version made from stainless steel is also resistant to corrosion and weathering, so it is also suitable for external use. In addition, the high-strength, precipitation-hardened pin makes extreme loads possible.
[Operation]
The threaded elements are unlocked by pressing the button.- 3D CAD data available
› Configure nowStarting from∗ ： 186.99 € Min. Shipping Days ： 2 Days *Unit price with basic configuration
-
Ring bolts similar to DIN 580 (K1333)
KIPP
· For hoisting and transport tasks
· Application sectors: machine and fixture construction, toolmaking, logistics, material handling- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 5.60 € Min. Shipping Days ： 4 Days *Unit price with basic configuration
-
› Configure now
Starting from∗ ： 1.59 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Lifting eye nuts (rotating), Steel
GANTER
Lifting eye nuts GN 583 are mounted in rotating bearings, allowing the direction of the force action to be adjusted and preventing inadvertent loosening or overturning (as potentially possible in lifting eye nuts DIN 582).
Lifting eye nuts GN 583 offer a high load carrying capacity and they are tested to meet safety standards (safety factor 4).
The rated load carrying capacity listed in the above table is clearly marked on the ring. It applies to the most unfavourable load application of the load types listed opposite.
Lifting eye nuts GN 583 comply with Mechanical Engineering Directive 2006 / 42 / EG and are BG tested.
The integrated RFID transponder clearly marks and identifies the sling and lifting gear, e.g. during the prescribed regular inspection.
The hexagon socket nut cannot be removed from the ring.- Volume Discount
- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 97.40 € Min. Shipping Days ： 4 Days *Unit price with basic configuration
-
Ball Lock Connectors, self-locking, with holder, compact construction
HALDER
Parts can be connected fast and easily with the ball lock connector in combination with the locating bushings.
The locating bushings are made from stainless steel. There are two versions available that can be mounted into wood and one version that can be mounted into plastic.
As a robust tool, the item is made from stainless steel. The ball lock connector is maintenance-free, soundless and secured against loss.
[Operation]
The balls are unlocked by pressing the knob.› Configure nowStarting from∗ ： 6.71 € Min. Shipping Days ： 2 Days *Unit price with basic configuration
-
Ring nuts DIN 582 (K0768)
KIPP
· For hoisting and transport tasks
· Application sectors: machine and fixture construction, toolmaking, logistics, material handling
· Version: steel or stainless steel- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 1.16 € Min. Shipping Days ： 4 Days *Unit price with basic configuration
-
› Configure now
Starting from∗ ： 1.50 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Lifting eye nuts, Stainless Steel A4
GANTER
The following guidelines of the Stainless Steel-Lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table.
The eye nut must be of fully screwd in to achieve a perfect contact between the two mating faces.
Both threads must be of a equal length and the base material of equal strength to that of the nut.
Operating instructions with more details and specifications are included with every delivery (see also www.ganter-griff.com/service).
The official DIN standard sheet specifies the additional sizes M42, M48, M56, M64, M72 x 6, M80 x 6 und M100 x 6.- Volume Discount
› Configure nowStarting from∗ ： 11.56 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Lifting eye nuts, Steel
GANTER
The following guidelines of the lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table.
The eye nut must be of fully screwd in to achieve a perfect contact between the two mating faces.
Both threads must be of a equal length and the base material of equal strength to that of the nut.
Operating instructions with more details and specifications are included with every delivery (see also www.ganter-griff.com/service).
The official DIN standard sheet specifies the additional sizes M42, M48, M56, M64, M72 x 6, M80 x 6 und M100 x 6.- Volume Discount
› Configure nowStarting from∗ ： 2.48 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
› Configure now
Starting from∗ ： 81.14 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
-
Lifting Pin, Self-Locking, Stainless Steel
HALDER
[Features]
· Has high corrosion and weather resistance enabling use outdoors
· Pin part uses hardened stainless steel and so has high strength
· Operating temperature range is to a maximum of 250°C
· Locating· Bushing use from 22350.0900 to 0.0936 (d1 = 8, 10, 12, 16) as well.
· Fitting for hanging that is speedy and simple to use yet solid. The movable shackle is equipped with a safety bar to prevent the button from being pushed unintentionally. A tap hole is not required for the item to be hung, only a H11 hole is needed.- 3D CAD data available
› Configure nowStarting from∗ ： 127.17 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Lifting eye nuts, Stainless Steel A2
GANTER
The following guidelines of the Stainless Steel-Lifting eye nuts DIN 582 have to be observed in addition to the load values given in the above table.
The eye nut must be of fully screwd in to achieve a perfect contact between the two mating faces.
Both threads must be of a equal length and the base material of equal strength to that of the nut.
Operating instructions with more details and specifications are included with every delivery (see also www.ganter-griff.com/service).
The official DIN standard sheet specifies the additional sizes M42, M48, M56, M64, M72 x 6, M80 x 6 und M100 x 6.- Volume Discount
› Configure nowStarting from∗ ： 5.40 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
Ring nuts similar to DIN 582 (K1334)
KIPP
· For hoisting and transport tasks
· Application sectors: machine and fixture construction, toolmaking, logistics, material handling- 2D / 3D CAD data available
› Configure nowStarting from∗ ： 5.23 € Min. Shipping Days ： 4 Days *Unit price with basic configuration
-
Locating· For Bushing Lifting Pin
HALDER
This bushing is a reliable holder for the safety of the lifting pin EH22350. [Features]
· Mounting is simple and reliable.
· Can be mounted to products made of various material.
· Can be used in narrow areas or blind holes.
· High corrosion resistance
· Wear resistant- 3D CAD data available
› Configure nowStarting from∗ ： 34.64 € Min. Shipping Days ： Same day *Unit price with basic configuration
-
› Configure now
Starting from∗ ： 8.06 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
-
Threaded Lifting Pins, self-locking, for centre holes according to DIN 332
HALDER
MaterialPin part
- • Heat-treated steel, tempered, manganese phosphated
• Stainless steel 1.4542, precipitation-hardenedPress button
- • Aluminium, orange, anodised
Threaded element
- • Stainless steel 1.4542, precipitation-hardened
Shackle
- • Heat-treated steel, tempered, manganese phosphated
• Stainless steel 1.4571Spring
- • Stainless Steel
Assembly
Threaded lifting pins can be mounted into a thread that is true to gauge.
Mounting:
- • Press in the button and hold it down.
• Insert the threaded lifting pin.
• Release the button (The button must be back in its original position.).
• Tighten the threaded lifting pin by hand, until it bears compleately on the bearing surface.
• It must be ensured that the threaded segments are engaged in the mounting thread.Dismantling:
- • Unscrew the threaded lifting pin approx. a quarter of a turn anticlockwise.
• Press in the button and hold it down.
• Remove the threaded lifting pin.
• Release the button.Operation
Each threaded lifting pin contains an instruction manual with an EC Declaration of Conformity.
- 3D CAD data available
› Configure nowStarting from∗ ： 189.97 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
-
ART 88536 FISCHER-Dübel
REYHER
Dübel u. Anker für Gerüste u. Fassaden (FISCHER); FISCHER-Dübel und Anker; Gerüsthalter (Dübel / Ringösen)- Volume Discount
› Configure nowStarting from∗ ： 2.04 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
-
› Configure now
Starting from∗ ： 14.09 € Min. Shipping Days ： 1 Day *Unit price with basic configuration
-
Threaded Lifting Pins, self-locking, with rotatable shackle
HALDER
MaterialPin part
- • Heat-treated steel, tempered, manganese phosphated
• Stainless steel 1.4542, precipitation-hardenedPress button
- • Aluminium, orange, anodised
Threaded element
- • Stainless steel 1.4542, precipitation-hardened
Shackle
- • Heat-treated steel, tempered, manganese phosphated
• Stainless steel 1.4571Spring
- • Stainless Steel
Assembly
Threaded lifting pins can be mounted into a thread that is true to gauge.
Mounting:
- • Press in the button and hold it down.
• Insert the threaded lifting pin.
• Release the button (The button must be back in its original position.).
• Tighten the threaded lifting pin by hand, until it bears compleately on the bearing surface.
• It must be ensured that the threaded segments are engaged in the mounting thread.Dismantling:
- • Unscrew the threaded lifting pin approx. a quarter of a turn anticlockwise.
• Press in the button and hold it down.
• Remove the threaded lifting pin.
• Release the button.Operation
Each threaded lifting pin contains an instruction manual with an EC Declaration of Conformity.
- 3D CAD data available
› Configure nowStarting from∗ ： 306.93 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
-
Threaded Lifting Pins, self-locking - INCH
HALDER
MaterialPin part
- • Heat-treated steel, tempered, manganese phosphated
• Stainless steel 1.4542, precipitation-hardenedPress button
- • Aluminium, orange, anodised
Threaded element
- • Stainless steel 1.4542, precipitation-hardened
Shackle
- • Heat-treated steel, tempered, manganese phosphated
• Stainless steel 1.4571Spring
- • Stainless Steel
Assembly
Threaded lifting pins can be mounted into a thread that is true to gauge.
Mounting:
- • Press in the button and hold it down.
• Insert the threaded lifting pin.
• Release the button (The button must be back in its original position.).
• Tighten the threaded lifting pin by hand, until it bears compleately on the bearing surface.
• It must be ensured that the threaded segments are engaged in the mounting thread.Dismantling:
- • Unscrew the threaded lifting pin approx. a quarter of a turn anticlockwise.
• Press in the button and hold it down.
• Remove the threaded lifting pin.
• Release the button.Operation
Each threaded lifting pin contains an instruction manual with an EC Declaration of Conformity.
Notes
- • This product is manufactured in INCH dimensions.
- 3D CAD data available
› Configure nowStarting from∗ ： 193.91 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
-
Threaded Lifting Pins, self-locking, with rotatable shackle - INCH
HALDER
MaterialPin part
- • Heat-treated steel, tempered, manganese phosphated
• Stainless steel 1.4542, precipitation-hardenedPress button
- • Aluminium, orange, anodised
Threaded element
- • Stainless steel 1.4542, precipitation-hardened
Shackle
- • Heat-treated steel, tempered, manganese phosphated
• Stainless steel 1.4571Spring
- • Stainless Steel
Assembly
Threaded lifting pins can be mounted into a thread that is true to gauge.
Mounting:
- • Press in the button and hold it down.
• Insert the threaded lifting pin.
• Release the button (The button must be back in its original position.).
• Tighten the threaded lifting pin by hand, until it bears compleately on the bearing surface.
• It must be ensured that the threaded segments are engaged in the mounting thread.Dismantling:
- • Unscrew the threaded lifting pin approx. a quarter of a turn anticlockwise.
• Press in the button and hold it down.
• Remove the threaded lifting pin.
• Release the button.Operation
Each threaded lifting pin contains an instruction manual with an EC Declaration of Conformity.
Notes
- • This product is manufactured in INCH dimensions.
- 3D CAD data available
› Configure nowStarting from∗ ： 311.03 € Min. Shipping Days ： 3 Days *Unit price with basic configuration
| Brand |
|---|
| Product Series |
| CAD |
| Starting from∗ |
| Min. Shipping Days |
| Screw Nominal (M) |
| Material |
| Strength Class (Steel) |
| Technical Standard |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
| Brand | GANTER | REYHER | GANTER | KIPP | GANTER | KIPP | KIPP | GANTER | HALDER | GANTER | HALDER | KIPP | REYHER | GANTER | HALDER | KIPP | REYHER | GANTER | GANTER | REYHER | HALDER | GANTER | KIPP | HALDER | REYHER | HALDER | REYHER | HALDER | HALDER | HALDER | HALDER |
| Product Series | Ball Lock Connectors, self-locking, with holder, compact construction | Threaded Lifting Pins, self-locking, for centre holes according to DIN 332 | Ball Lock Connectors, self-locking, holder / Bushing holder, function Nominal mm / mm / mm | Threaded Lifting Pins, self-locking, with rotatable shackle - INCH | |||||||||||||||||||||||||||
| CAD |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| ||||||||||||||
| Starting from∗ | 2.48 € *Unit price with basic configuration Volume Discount | 0.81 € *Unit price with basic configuration Volume Discount | 80.20 € *Unit price with basic configuration Volume Discount | 3.16 € *Unit price with basic configuration | 5.18 € *Unit price with basic configuration Volume Discount | 1.25 € *Unit price with basic configuration | 3.16 € *Unit price with basic configuration | 11.58 € *Unit price with basic configuration Volume Discount | 67.17 € *Unit price with basic configuration | 176.26 € *Unit price with basic configuration Volume Discount | 186.99 € *Unit price with basic configuration | 5.60 € *Unit price with basic configuration | 1.59 € *Unit price with basic configuration Volume Discount | 97.40 € *Unit price with basic configuration Volume Discount | 6.71 € *Unit price with basic configuration | 1.16 € *Unit price with basic configuration | 1.50 € *Unit price with basic configuration Volume Discount | 11.56 € *Unit price with basic configuration Volume Discount | 2.48 € *Unit price with basic configuration Volume Discount | 81.14 € *Unit price with basic configuration Volume Discount | 127.17 € *Unit price with basic configuration | 5.40 € *Unit price with basic configuration Volume Discount | 5.23 € *Unit price with basic configuration | 34.64 € *Unit price with basic configuration | 8.06 € *Unit price with basic configuration Volume Discount | 189.97 € *Unit price with basic configuration | 2.04 € *Unit price with basic configuration Volume Discount | 14.09 € *Unit price with basic configuration | 306.93 € *Unit price with basic configuration | 193.91 € *Unit price with basic configuration | 311.03 € *Unit price with basic configuration |
| Min. Shipping Days | Same day | Same day | Same day | 4 Days | Same day | 4 Days | 4 Days | Same day | Same day | 4 Days | 2 Days | 4 Days | Same day | 4 Days | 2 Days | 4 Days | Same day | Same day | Same day | 3 Days | Same day | Same day | 4 Days | Same day | 3 Days | 3 Days | 3 Days | 1 Day | 3 Days | 3 Days | 3 Days |
| Screw Nominal (M) | M 8 ～ M 36 | - | M 6 ～ M 36 | 6 ～ 24 | M 8 ～ M 24 | 8 ～ 24 | 5 ～ 20 | M 10 ～ M 24 | - | M 12 ～ M 24 | M14 ～ M30 | 8 ～ 20 | - | M 8 ～ M 30 | - | 8 ～ 24 | - | M 10 ～ M 24 | M 8 ～ M 36 | - | - | M 8 ～ M 24 | 8 ～ 20 | - | - | M10 ～ M24 | - | - | M10 ～ M24 | - | - |
| Material | Steel | - | - | Stainless Steel ～ Steel | Stainless Steel | Stainless Steel ～ Steel | Stainless Steel ～ Steel | Stainless Steel | - | - | - | Stainless Steel | - | - | - | Stainless Steel ～ Steel | - | Stainless Steel | Steel | - | - | Stainless Steel | Stainless Steel | - | - | - | - | - | - | - | - |
| Strength Class (Steel) | - | - | - | 8.8 | - | - | 8.8 | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - | - |
| Technical Standard | DIN | DIN | - | - | - | - | - | - | - | - | - | - | DIN | - | - | - | DIN | - | - | DIN | - | - | - | - | DIN | - | - | - | - | - | - |
Loading...
Filter by:
Stock
-
- Show only stock items
-
Screw Nominal (M)
-
Material
-
Strength Class (Steel)
CAD data type
-
- 2D
- 3D
Standard shipping days
-
- All
- Same day
- 1 Day or Less
- 2 Days or Less
- 3 Days or Less
- 4 Days or Less
- 5 Days or Less
- 7 Days or Less
- 8 Days or Less
Categories related to Lifting Eyebolts
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.