6 Series / slot width 8 / 60x90mm

Configurable Length Extrusion Specification Table

 

Type	Material	Surface Treatment	Part Number	L 0.5 mm Increments (Tolerance ±0.5 mm)	Mass kg/m	Sectional Area mm2	Cross Sectional Moment of Inertia mm4
							ℓx	ℓy
HFS	EN AW-6061-T5 Equiv.	Clear Anodize	HFS6－6090	50 to 4000	3.1	1147	52.6 × 104	111.0 × 104
NEFS	EN AW-6063-T5 Equiv.	Clear Anodize	NEFS6－6090	50 to 4000	3.1	1147	52.6 × 104	111.0 × 104

[ ! ] Extrusions without anodizing are also available.
[ ! ] Applicable to 6,000 mm depending on products.
[ ! ] Not applicable to some extrusions.

Fixed Length Extrusion (Effective Length 4,000 mm) Specification Table

[ ! ] Part numbers beginning with the character "K" indicate Fixed Length Extrusion.

Type	Material	Surface Treatment	Part Number	Lmm (No tolerance regulation)	Sectional Area mm2	Cross Sectional Moment of Inertia mm4
						ℓx	ℓy
HFS	EN AW-6061-T5 Equiv.	Clear Anodize	KHFS6－6090	4000	1147	52.6 × 104	111.0 × 104
NEFS	EN AW-6063-T5 Equiv.	Clear Anodize	KNEFS6－6090	4000	1147	52.6 × 104	111.0 × 104

[ ! ] An effective Length of 4,000 mm indicates the extrusion with 4,000 mm or more effective length.
The actual length with extra lengths on ends is more than 4000 mm (several tens of mm).
Fixed Length Extrusions need to be cut by users thus the exact length cannot be specified.

Alterations

[ ! ] MISUMI configurable length aluminum extrusion product can be utilized for structure building with highly enhanced design flexibility when the following various alteration options are applied.
Some alterations are not applicable depending on types and sizes.

Type	Alterations	Alteration Codes	App. Example	Contents
> End Tapping	End Tapping (Center Hole)	LTP/RTP/TPW LHP/RHP/HPW		Adds tapped holes on extrusion ends. Blind Joints which require this alteration (Screw Joint / Simple Joint)
	End Tapping (4 Side Holes)	LSP/RSP/SPW		Adds tapped holes on extrusion corner ends.
> Cutting Method Change	High Precision Cut	SC		Applies High Precision Cut with an overall length tolerance of L±0.2 (Standard = L±0.5). * Only applicable to L ≤ 1,500
	45-Degree Cut	L□T45/R□T45		Cuts with 45-degree angle.
> Drill Wrench Hole	Wrench Hole in Fixed Position	LWP/RWP		Wrench access hole(s) for Blind Joints are drilled. The hole location will be aligned with the mating extrusion’s tapped hole location. Blind Joints which require this alteration (Screw Joint / Single Joint / Tapping Joint)
	Extrusion End Cap The hole position moves by thickness	FL/FR		Offsets the wrench access hole for the thickness of Extrusion End Cap (3 mm). The extrusion end cap will be flat with the adjacent extrusion surface.
	Wrench Hole in Specified Position	AH/BH/AV/BV		Adds a wrench hole in a desired position from the left end. Use for Blind Jointing in beam sections, etc.
> Counterboring	Counterbores in Specified Position	Z6/XA100		Adds a counterbored hole in a desired position from the left end. Can be used for connecting extrusions or installing tables, etc.
> Blind Joints Dedicated Holes	D Hole	LDH/RDH		Adds required holes for Single Joint connections. (Single Joints)
	S Hole	LSH		Adds required holes for Pre-Assembly. Insertion Double Joint connections. (Pre-Assembly Insertion Double Joints)
	M Hole	LMH		Adds required holes for Post-Assembly Insertion Double Joints, Center Joint connections. (Post-Assembly Insertion Double Joint / Center Joint)
	L Hole	JLP		Adds required holes for Parallel Joint connections. (Parallel Joints)
> Other Machining	GNFS Series GFS Series End Tapping	LTS/RTS/TSW		Adds tapped holes on extrusion ends. This process is required for using extrusion end cap of the high rigidity plate type. (Plates for High Rigidity Type)
	HFSR End Tapping	LTS/RTS/TSW		Necessary alteration to use Ends Protection Plates for HFSR series.
	End Face C Chamfering	CW		Adds C Chamfering on extrusion ends.
	Labeling	ZZZ		Adds a sticker with catalog No. etc. on the aluminum extrusions. Although number of characters are limited, customer's own serial number or unit number can be labeled.