Configure
- A(mm)[10-300/1mm units]
- B(mm)[5-300/1mm units]
- T(mm)
- 1
- 1.5
- 1.6
- 2
- 2.3
- 3
- 3.2
- 4
- 4.5
- 5
- 6
- CAD
- 2D
- 3D
- Est. shipping days
- All
- Within 7 working days
- Within 9 working days
- Within 20 working days
Sheet Metal Mounting Plate / Bracket - Custom Dimensions Type - JTNAS
Part number:
possible part numbers found.Outline drawing and specifications table
JTNAS
[ ! ]Green colored parameters can be omitted. If the parameter setting is omitted, the holes will be evenly distributed about the center.
[ ! ]For details on specifications and machining limits, see >> here
[ ! ]For details on specifications and machining limits, see >> here
■Hole Type Selection Chart
| Hole Type | Bolt Hole | Tapped Hole (Coarse) |
| Code | N・NA | M・MA |
| Shape Diagram | [ ! ]  |  |
| [ ! ]For the d dimensions, refer to the "N, NA Machining Dimensions" section below the Specifications Table |
| Part Number | [ M ]Material | [ S ]Surface Treatment | ||
| Type | Material Symbol | |||
| JTNAS | SP | T0.8~3.2 T4.5~6.0 T9.0 | : EN 1.0330 Equiv. : EN 1.0320 Equiv. (hot coiled) : EN 1.0038 Equiv.(Black) | − |
| SPB | Black Oxide | |||
| SPU | Trivalent Chromate (Clear) | |||
| SPK | Trivalent Chromate (Black) | |||
| AM | EN AW-5052 Equiv. | − | ||
| AMW | Anodize (Clear) | |||
| AMB | Anodize (Black) | |||
| SUD | T0.8~6.0 T9.0 | : EN 1.4301 Equiv. (Passivated 2B) : EN 1.4301 Equiv.(No.1) | − | |
Specification Table
| Part Number | － | A | － | B | － | T | － | X | － | F | － | Y | － | Hole Specification (1) Code / Nominal Dia. | － | L | V | － | S | － | Hole Specification (2) Code / Nominal Dia. | |||
| － | ||||||||||||||||||||||||
| Type | － | Material Symbol | ||||||||||||||||||||||
| JTNAS | － | SP | － | A120 | － | B80 | － | T2.3 | － | X10 | － | F30 | － | Y40 | － | N8 | － | L80 | － | V30 | － | S40 | － | MA4 |
| Part Number | 1 mm Increments | Selection | X | F | Y | Hole Specification (1) | L | V | S | Hole Specification (2) | ||||||
| Type | Material Symbol | A | B | T | Code / Specify Method | Code / Specify Method | ||||||||||
| JTNAS | SP SPB SPU SPK | 10 ～ 300 | 5 ～ 300 [ ! ] | 0.8 ・ 1.0 ・ 1.2 ・ 1.6 ・ 2.3 3.2 ・ 4.5 ・ 6.0 ・ 9.0 | Configurable 0.1 mm Increments | Configurable 0.1 mm Increments | ||||||||||
| N (Bolt Hole) | M (Tapped Holes) | NA (Bolt Hole) | MA (Tapped Holes) | |||||||||||||
| 0・3・4・5 | 0・3・4・5 | 0・3・4・5 | 0・3・4・5 | |||||||||||||
| AM AMW AMB | 1.0 ・ 1.5 ・ 2.0 ・ 3.0 ・ 4.0 ・ 5.0 | |||||||||||||||
| 6・8・10 | 6・8・10 | 6・8・10 | 6・8・10 | |||||||||||||
| (Select) | (Select) | (Select) | (Select) | |||||||||||||
| SUD | 0.8 ・ 1.0 ・ 1.2 ・ 1.5 ・ 2.0 3.0 ・ 4.0 ・ 5.0 ・ 6.0 ・ 9.0 | [ ! ] | [ ! ] | [ ! ] | [ ! ] | |||||||||||
| [ ! ]For T6.0, B ≥ 6, for T9.0, B ≥ 9 | ||||||||||||||||
| [ ! ]If the specified hole location is close to the edges, the hole may be deformed but will be machined as specified if within machining limits. | ||||||||||||||||
[ ! ]N・NA Machining Dimension Table
| N・NA Specified Value | Through Hole Diameter (d) |
| 0 | (No Hole) |
| 3 | 3.5 |
| 4 | 4.5 |
| 5 | 5.5 |
| 6 | 6.5 |
| 8 | 9 |
| 10 | 11 |
[ ! ]Hole Machining Table
[ ! ]T = 1.0 is not applicable for tapped holes to AM, AMW, or AMB
| T | N・NA (Bolt Hole) | M・MA (Tapped Holes) |
| 0.8 | 0・3・4・5・6・8・10 | 0 |
| 1.0、1.2 | 0・3 | |
| 1.5、1.6 | 0・3・4 | |
| 2.0、2.3 | 0・3・4・5・6 | |
| 3.0、3.2 | 0・3・4・5・6・8 | |
| 4.0～6.0 | 0・3・4・5・6・8・10 | |
| 9.0 | 0・5・6・8・10 | 0・5・6・8・10 |
Alterations
| Alteration | Corner cut | ||
 | |||
| Code | CC | ||
| Spec. | CC = 1 mm Increments 1 ≤ CC ≤ 10
(Example) ... -CC5 | ||
■Specifications, Machining Limits
[ ! ]1. See the figure below for tolerances
[Standard Machined Dimension Tolerances]
*For sheet metals, Class B Tolerance stipulated in JIS B 0408, General dimensional tolerances for parts formed
by press working from sheet metal is used.:
[Standard Machined Dimension Tolerances]
| Product | Dimension Range (A, B Dimension) | 6 or less | Over 6, and 30 or less | Over 30, and 120 or less | Over 120, and 400 or less |
| Sheet Metal (No Bending) | Tolerance（a・b） | ±0.1 | ±0.2 | ±0.3 | ±0.5 |
by press working from sheet metal is used.:
[ ! ]2. Burr height 0.1 or less
[ ! ]3. In case of the thin plates, the tap ridges may be crushed, so please be careful when tightening.
[ ! ]4. When changing to a specification without holes, anodizing with T4 or more may cause a hang hole to be formed as shown in the figure below.
[ ! ]5. There are machining limits for thickness between hole and hole or between hole and end face. (Example: "b" on the drawing below)
| T | b | ||
| EN 1.0330 Equiv. EN 1.0320 Equiv. (hot coiled) EN 1.0038 Equiv. | |||
| EN AW-5052 Equiv. | EN 1.4301 Equiv. | ||
| 0.8 | ー | 0.8 | 1 |
| 1.0 | 1.0 | 1.0 | 1 |
| 1.2 | ー | 1.2 | 1 |
| 1.6 | 1.5 | 1.5 | 1 |
| 2.3 | 2.0 | 2.0 | 1.5 |
| 3.2 | 3.0 | 3.0 | 1.5 |
| 4.5 | 4.0 | 4.0 | 2 |
| ー | 5.0 | 5.0 | 2.5 |
| 6.0 | ー | 6.0 | 2.5 |
| 9.0 | ー | 9.0 | 4 |
■Appearance per Material (Surface Treatment) and Machining Method
| None | Black Oxide | Trivalent Chromate (Clear) | Trivalent Chromate (Black) | |
| SP | SPB | SPU | SPK | |
| EN 1.0330 Equiv. T0.8～3.2 |  |  |   |   |
| EN 1.0320 Equiv. (hot coiled) T4.5～6.0 |  |  |  |  |
| EN 1.0038 Equiv. （Black） T9.0 |  |  |  |  |
| None | Anodize (Clear) | Anodize (Black) | |
| AM | AMW | AMB | |
| EN AW-5052 Equiv. |  |  |  |
| None | |
| SUD | |
| EN 1.4301 Equiv. (Passivated 2B) T0.8～6.0 |  |
| EN 1.4301 Equiv.（No.1） T9.0 |  |
Part number list
Number of items
| Part number |
|---|
Unit price (excluding VAT)(Unit price including VAT) | Standard shipping days |
|---|
- ( - ) | 7 working days |
- ( - ) | 20 working days |
- ( - ) | 20 working days |
- ( - ) | 7 working days |
- ( - ) | 9 working days |
- ( - ) | 7 working days |
- ( - ) | 7 working days |
- ( - ) | 7 working days |
Catalog
Loading...