Configure
- External Dimension A(mm)[25-200/0.1mm units]
- External Dimension B(mm)[10-200/0.1mm units]
- Plate Thickness t(mm)[3-30/0.1mm units]
- CAD
- 2D
- 3D
- Est. shipping days
- All
- Within 7 working days
- Within 20 working days
- Within 22 working days
6 Surface Milling Machine Plates/Brackets. Outer Diameter Configurable. HFNRA
Part number:
possible part numbers found.Outline drawing and specifications table
HFNRA Common Dimension
[ ! ] Hole pitch dimension tolerance conforms to JIS B 0405 Class m.
[ ! ]
[ ! ] Hole pitch dimension tolerance conforms to JIS B 0405 Class m.
[!] Thickness (T) tolerance can be changed (Refer to the "Alterations" section.)
[ ! ] Thickness parallelism is 0.05 per 100 mm
[ ! ] C0.2 to C0.5, unless otherwise specified
[!] Orientation of Slotted Holes can be changed (Refer to the "Alterations" section.)
[!] Green colored parameters can be omitted. If the parameter setting is omitted, the holes will be evenly distributed about the center.
[ ! ] Thickness parallelism is 0.05 per 100 mm
[ ! ] C0.2 to C0.5, unless otherwise specified
[!] Orientation of Slotted Holes can be changed (Refer to the "Alterations" section.)
[!] Green colored parameters can be omitted. If the parameter setting is omitted, the holes will be evenly distributed about the center.
■Hole Type Selection Chart
■Machining Limits
There are machining limits for thickness between hole and hole or between hole and end face.
(Example: "b" on the drawing below)
| Hole Type | Tapped Hole | Bolt Hole | Counterbore Front | Counterbore Back | Through Hole | |||||||||||||||||||||||||||||||||||||||||||||
| Code | M·MA | N・NA | Z·ZF | ZB | DA | |||||||||||||||||||||||||||||||||||||||||||||
| Shape Diagram |  |  |  |  |  | |||||||||||||||||||||||||||||||||||||||||||||
| Machining Specifications | Effective Tap Length Max. M, MA × 2 [ ! ] When T ≥ M × 3, tap pilot hole might not go through. |
|
| |||||||||||||||||||||||||||||||||||||||||||||||
■Machining Limits
There are machining limits for thickness between hole and hole or between hole and end face.
(Example: "b" on the drawing below)
| Part Number | [M] Material | [S] Surface Treatment | |
| Type | Material Symbol | ||
| HFNRA | SC | EN 1.1206 Equiv. | — |
| SCB | Black Oxide | ||
| SCM | Electroless Nickel Plating | ||
| AM | EN AW−5052 Equiv. | — | |
| AMW | Anodize (Clear) | ||
| AMB | Anodize (Black) | ||
| SU | EN 1.4301 Equiv. | — | |
| Part Number | 0.1 mm Increments | X | Y | Hole Specification (1) | K | L | Hole Specification (2) | J | |||||
| Type | Material Symbol | A | B | T | Code | Nominal Dia. | Code | Nominal Dia. | |||||
| HFNRA | SC SCB SCM AM AMW AMB SU | 25.0 ～ 200.0 | 10.0 ～ 200.0 | 3.0 ～ 30.0 [ ! ] | 0.1 mm Increments | N [ ! ] [ ! ] For the machining dimensions , see Hole Type Selection Chart. | 0 (No Hole) 3 4 5 6 8 10 12 14 16 | 0.1 mm Increments [ ! ]K ≤ N × 10 | NA [ ! ] [ ! ] For the machining dimensions , see Hole Type Selection Chart. | 0 (No Hole) 3 4 5 6 8 10 12 14 16 | 0.1 mm Increments [ ! ]J ≤ NA × 10 | ||
| [ ! ]For AMW and AMB, T ≥ 5 [ ! ] For SU, T ≤ 25.0 | |||||||||||||
Specification Table
| Part Number | — | A | — | B | — | T | — | X | — | V | — | Y | — | W | — | Hole Specification (1) Code Nominal Dia. | — | K | — | L | — | H | — | D | — | F | — | S | — | G | — | Hole Specification (2) Code Nominal Dia. | — | J | ||
| Type | — | Material Symbol | ||||||||||||||||||||||||||||||||||
| HFMCC | — | AMB | — | A100 | — | B80 | — | T10 | — | X15 | — | V70 | — | Y10 | — | W60 | — | Z6 | — | L50 | — | H40 | — | D30 | — | F50 | — | MA6 | ||||||||
Alteration
| Alterations | Corner Cut Change | Plate thickness (T dim.) Tolerance Change | Slotted Hole Angle Change | ||||||
 |  |  | |||||||
| Code | CC | TKC·THC | RC | ||||||
| Spec. | Changes corner cuts. CC = 1 mm Increments [ ! ]1 ≤ CC ≤ 50
Example: ... -CC10 | Changes Plate thickness (T dim.) Tolerance. TKC: Tolerance ±0.05 THC: Tolerance ±0.02 [ ! ] Only SC, SCB and SCM material symbols are applicable [NG] TKC and THC cannot be specified simultaneously
Example: ... -TKC, ... -THC | Slotted holes are changed as shown above. [!] Note the dimensional relationship
(Example) ... -RC |
Part number list
Number of items
| Part number |
|---|
Unit price (excluding VAT)(Unit price including VAT) | Standard shipping days |
|---|
- ( - ) | 7 working days |
- ( - ) | 22 working days |
- ( - ) | 22 working days |
- ( - ) | 7 working days |
- ( - ) | 20 working days |
- ( - ) | 20 working days |
- ( - ) | 7 working days |
Catalog
Loading...