Confirmed
- Pipe Port Type
- Female Thread
- Plumbing Thread Type
- Rc (R)
- Rc
- Nominal Pipe Thread Size
- 1/4
- 1/4
- Rated Pressure Range
- Accuracy(%F.S.)
- Micro switch load capacity
- Scale plate pressure unit
- Type
- CAD
- 2D
- 3D
- Est. shipping days
- All
- Within 22 working days
Pressure Switch IS3000 Series (IS3000-02L2)
Product information
Specifications of Pneumatic Pressure Switch IS3000 Series
External appearance of IS3100 (Gasket mount)
External appearance of IS3000-02 (Rc1/4 thread connection)
External appearance of IS3110 (Gasket mount)
External appearance of IS3010-02 (Rc1/4 thread connection)
Dimensions
(Units: mm)
Dimensional drawing of IS3000 Series
Diagram
Structural drawing of IS3000-02/3010-02 (1/4 thread connection)
| Number | Part Name | Material |
|---|---|---|
| 1 | Adjustment screw | Rolled steel |
| 2 | Adjusting spring | Rolled steel |
| 3 | Lever | Rolled steel plate |
| 4 | Piston | Polyacetal |
| 5 | Microswitch | - |
| 6 | Bottom cover | Aluminum diecast |
| * 7 | O-ring | NBR |
* Gasket mount type only
Model
| Model | Piping Method | Micro switch type | Micro switch minimum applicable load |
|---|---|---|---|
| IS3000-02 | Rc1/4 thread connection | Standard type | 5 V DC 160 mA |
| IS3100 | Gasket mount | ||
| IS3010-02 | Rc1/4 thread connection | Microload type | 5 V DC 1 mA |
| IS3110 | Gasket mount |
Specifications
JIS symbol
| Fluid | Air and inert gas |
|---|---|
| Proof Pressure | 1.0 MPa |
| Maximum operating pressure | 0.8 MPa |
| Pressure Adjustment Range | 0.1 to 0.7 MPa |
| Ambient and fluid temperature | -5 to 60℃ (No freezing) |
| Contact | 1ab |
| Scale error | ±0.1 MPa |
| Hysteresis | 0.05 MPa or less |
| Repeat accuracy | ±0.05 MPa |
| Protective Enclosure | IP40 equivalent |
| Weight | 0.15 kg |
Microswitch rating
| Model | IS3000 IS3100 | IS3010 IS3110 | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| Load | Non-inductive load (A) | Inductive load (A) | Non-inductive load (A) | |||||||
| Load resistance | Lamp load | Inductive load | Electric motor load | Load resistance | ||||||
| Rated Voltage (V) | Circuits | |||||||||
| Normally Closed Circuit | Normally Open Circuit | Normally Closed Circuit | Normally Open Circuit | Normally Closed Circuit | Normally Open Circuit | Normally Closed Circuit | Normally Open Circuit | Normally Closed Circuit | Normally Open Circuit | |
| AC125 | 5 | 1.5 | 0.7 | 3 | 2.5 | 1.3 | 0.1 | |||
| AC250 | 3 | 1 | 0.5 | 2 | 1.5 | 0.8 | - | |||
| DC30 | 4 | 2 | 3 | 3 | 0.1 | |||||
| DC125 | 0.4 | 0.05 | 0.4 | 0.05 | - | |||||
- * Insulation resistance 100 MΩ or more (At 500 V DC by insulation resistance tester)
- * Withstand voltage 1,500 V AC 50/60 Hz for 1 minute (Withstand voltage of the product with neon lamp is 1,000 V AC for 1 minute)
Notes
About wiring
- * 1When using a product with the indicator light, refer to the wiring examples to wire the indicator light.
- * 2There are 2 name plates inside the device, "Neon lamp goes off when the pressure rises" and "Neon lamp lights when the pressure rises". The relevant plate is required to be pasted on the position outside the device where it can be easily checked.
- * 3The screws used for the terminals are M3.
Mounting and piping
- * 1 Some space is required for maintenance. The adjustment screw section on the top of the main unit may obstruct maintenance and the change of pressure regulation.
- * 2The mounting direction can be horizontal or vertical.
Pressure setting
- * 1For the pressure setting, turning the adjustment screw is required. The set pressure increases when the screw is turned to the plus (H) side on the top of the cover, and decreases when turned to the minus (L) side.
- * 2It is necessary to use a straight-slot screwdriver for the pressure setting and to fix it with a lock nut after setting in order to avoid deviation of the set pressure.
- * 3Hysteresis (width of ON-OFF) is fixed.
- * 4The switching setting display scale is the set value when the pressure rises.
Operating environment
- * 1It cannot be used in places where water or oil is scattered. Since it is an open type structure, if water or oil gets inside, the electric circuit will corrode, resulting in malfunction or damage.
- * 2Operating fluids are dedicated for air and inert gas. Liquids cannot be used.
- * 3It is completely unacceptable to use in an atmosphere of flammable liquid or flammable gas.
- * 4Since it does not have an explosion-proof structure, it may cause an explosion disaster.
Other
- * 1Spare parts are only lamp assemblies. Other parts cannot be replaced by a user, so it is necessary to request repair.
It is possible to change to L1, L2, and L5 by replacing each lamp assembly.
Lamp assembly
For 110 V AC: 1530118-1
For 220 V AC: 1530118-2
For 24 V DC: 1530118-5 - * 2*See the catalog for product information other than the listed above.
- * 3The product images are representative only.
More Information
Basic information
A pressure switch made by SMC
[Features]
· Can be used for micro loads around 10 mA, for relays, programmable controllers, etc.
· With indicator light
Caution
- See catalog for specification details.
- Product pictures are representations. CAD data is not supported for some model numbers.
Catalog
Part number has been confirmed