CARBIDE PILOT PUNCHES
| Shank type | Material | Tip shape |
Shank diameter tolerance |
Standard | Lapping | TiCN coating |
|---|---|---|---|---|---|---|
| Carbide standard punches | ||||||
  |
V30(HIP) | R | Dm5 | WSTA□ | L-WSTA□ | H-WSTA□ |
D |
A-WSTA□ | AL-WSTA□ | AH-WSTA□ | |||
| Taper | Dm5 | WTPA□ | L-WTPA□ | H-WTPA□ | ||
| D |
A-WTPA□ | AL-WTPA□ | AH-WTPA□ | |||
| Carbide punches with key grooves | ||||||
  |
V30(HIP) | R | Dm5 | WKSTA□ | Alteration SC | |
| D |
A-WKSTA□ | |||||
D |
B-WKSTA□ | |||||
| Taper | Dm5 | WKTPA□ | ||||
| D |
A-WKTPA□ | |||||
| D |
B-WKTPA□ | |||||
| Carbide straight punches | ||||||
  |
V30(HIP) | R | - | WSTC | L-WSTC | H-WSTC |
| Taper | - | WTTC | L-WTTC | H-WTTC | ||
| Carbide straight punches with key grooves | ||||||
  |
V30(HIP) | R | - | WKSTC | Alteration SC | |
| Taper | - | WKTTC | ||||
| Carbide punches for fixing to stripper plate | ||||||
   |
V30(HIP) | R | Dm5 | WSPTP | L-WSPTP | H-WSPTP |
| D |
A-WSPTP | AL-WSPTP | AH-WSPTP | |||
| Taper | Dm5 | WTPTP | L-WTPTP | H-WTPTP | ||
| D |
A-WTPTP | AL-WTPTP | AH-WTPTP | |||
| Sharp angle |
Dm5 | WAPTP | L-WAPTP | H-WAPTP | ||
| D |
A-WAPTP | AL-WAPTP | AH-WAPTP | |||
| Carbide straight punches for fixing to stripper plate | ||||||
   |
V30(HIP) | R | - | WSPT | L-WSPT | H-WSPT |
| Taper | - | WTPT | L-WTPT | H-WTPT | ||
| Sharp angle |
- | WAPT | L-WAPT | H-WAPT | ||
| Carbide punches for fixing to stripper plates, tip R and taper combined
type, minus head tolerance |
||||||
 |
V30(HIP) | R & Taper |
Dm5 | WSPTPF | L-WSPTPF | H-WSPTPF |
| Carbide straight punches for fixing to stripper plates Tip R and taper
combined type, minus head tolerance |
||||||
 |
V30(HIP) | R & Taper |
- | WSPTF | L-WSPTF | H-WSPTF |
| Movable carbide punches | ||||||
   |
V30(HIP) | R | Dg6 | WSUPT | L-WSUPT | H-WSUPT |
D |
A-WSUPT | AL-WSUPT | AH-WSUPT | |||
| Taper | Dg6 | WTUPT | L-WTUPT | H-WTUPT | ||
| D |
A-WTUPT | AL-WTUPT | AH-WTUPT | |||
| Sharp angle |
Dg6 | WUPT | L-WUPT | H-WUPT | ||
| D |
A-WUPT | AL-WUPT | AH-WUPT | |||
■Shank diameter tolerance Dm5
| D | Tolerance(Units: mm) |
|---|---|
| 1.6 | +0.006 +0.002 |
| 2.0 | |
| 2.5 | |
| 3 | |
| 4 | +0.009 +0.004 |
| 5 | |
| 6 | |
| 8 | +0.012 +0.006 |
| 10 | |
| 13 | +0.015 +0.007 |
| 16 |
■Shank diameter tolerance Dg6
| D | Tolerance(Units: mm) |
|---|---|
| 1.6 | -0.002 -0.008 |
| 2.0 | |
| 2.5 | |
| 3 | |
| 4 | -0.004 -0.012 |
| 5 | |
| 6 | |
| 8 | -0.005 -0.014 |
| 10 | |
| 13 | -0.006 -0.017 |
| 16 |
