GANTER Grub Screws

?* Information on days to ship and prices

• • Promotional pricing

  

  Grub screws with brass / plastic pivot, Stainless Steel

  GANTER

  Stainless Steel-Grub screws GN 913.5 with pivot in brass or plastic are used in applications, where marks and damage on the workpiece are unacceptable.
  

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	2.46 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Grub screws with ball point

  GANTER

  Grub screws GN 632.1 with ball point are as a rule used with thrust pads GN 631.
  The ball-Ø d2 is smaller than the thread core-Ø, which allows fitting over the ball end.
  The combination of grub screws GN 632.1 and thrust pads GN 631 with gripping elements easily makes clamping screws of many different types.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	1.20 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Grub screws with Brass / Plastic pivot, Steel

  GANTER

  Grub screws GN 913.3 with pivot in brass or pivot are used in applications, where marks and damage on the workpiece are unacceptable.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	0.98 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Grub screws with retaining magnet, Steel

  GANTER

  Grub screws GN 913.6 with retaining magnet are a shielded magnetic system.
  Suitable e.g. as workpiece stop, with the magnet holding the workpiece in place.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	5.56 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Grub screws, Stainless Steel

  GANTER

  Stainless-Steel-Grub screws GN 632.5 with ball point are as a rule used with Stainless Steel-Thrust pads GN 631.5.
  The ball-Ø d2 is smaller than the thread core-Ø, which allows fitting over the ball end.
  The combination of grub screws GN 632.1 and thrust pads GN 631.5 with gripping elements easily makes clamping screws of many different types.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	1.52 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Grub screws with thrust point, blackened

  GANTER

  The thrust point of these screws DIN 6332 is designed to be used with or without the thrust pad for clamping.
  The snap ring resp. spring is a simple and quick method to connect the thrust pad to the grub screw.
  Through the combination of grub screws DIN 6332 with various handles or knobs, simple clamping screws can be created.

  • Volume Discount

  Starting from∗ ：	0.90 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Thrust pads Steel / Plastic

  GANTER

  Thrust pads GN 6311.1 are used in conjunction with grub screws fitted with thrust point (grub screws DIN 6332, tommy screws DIN 6304 and DIN 6306) to transmit clamping force. They align themselves on uneven and non-parallel surfaces and thus prevent the rotating force being transmitted to the workpiece.
  The plastic cap prevents damage to delicate workpieces.
  The unique shape of the non-removable retaining ring permits easy insertion and removal of grub screws into or from the thrust pad.
  Thrust pads GN 6311.1 can be used in conjunction with DIN 6332 grub screws as levelling pad.
  

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	3.40 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Thrust pads, Plastic

  GANTER

  Thrust pads GN 631 are normally combined with ball point grub screws GN 632.1 / GN 632.5 They are easy to press-on to the ball point of the grub screw by hand.
  

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	0.78 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Grub screws with hardened pivot

  GANTER

  Grub screws GN 913.2 with hardened spherical pivot (Type A) are used in such cases where point contact is required. They are a lower cost alternative to ball point screws GN 605.
  Grub screws GN 913.2 with hardened pointed pivot (Type B) offer an alternative form of finish.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	2.46 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Levelling feet, Steel

  GANTER

  Levelling feet GN 6311.4 are normally used when a thread is present at the machine side to adjust the height.
  The pin diameter d3 is smaller than the core diameter of the thread, with the effect that the screw can be turned in at the pin. The pressure pin is easily inserted into the plate, with the retaining ring ensuring that the assembly is secure in axial direction.
  The static load of the levelling feet GN 6311.4 is limited by the laod capacity of the grub screw (Tensile strength class 5.8). The static load values (only valid for Type OS/KS) in the above table refer to a net vertical load in relation to the ball socket. Under normal operating conditions side loading or angular loading is not uncommon and the load capacity would be considerable reduced which must be taken into consideration.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	16.28 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing

  

  Thrust pads / Steel / with circlip / DIN 6311

  GANTER

  Thrust pads DIN 6311 are utilized to transmit clamping forces. They lean to uneven and unparallel surfaces and eliminate the transmission of any screw turning movement to the workpiece.
  Hints for installation
  The thrust pad has to be held at an angle allowing the circlip to drop to the bottom of its groove with the split end downwards. The thrust pin is then offered up to the split end of the circlip at the lowest possible angle and pressed home.

  • Volume Discount

  Starting from∗ ：	2.10 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Grub screws with thrust point, zinc plated

  GANTER

  The thrust point of these screws DIN 6332 is designed to be used with or without the thrust pad for clamping.
  The snap ring resp. spring is a simple and quick method to connect the thrust pad to the grub screw.
  Through the combination of grub screws DIN 6332 with various handles or knobs, simple clamping screws can be created.

  • Volume Discount

  Starting from∗ ：	2.88 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• • Promotional pricing

  

  Thrust pads, Stainless Steel

  GANTER

  Thrust pads GN 631.5 are normally combined with ball point grub screws GN 632.5. They are easy to press-on to the ball point of the grub screw by hand.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	6.20 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Stainless Steel-Grub screws thrust point

  GANTER

  [Specifications]
  ・Type: SKN. with thrust point. not hardened
  ・Material: NI. Stainless Steel
  
  The thrust point of these screws DIN 6332 is designed to be used with or without the thrust pad for clamping. The pin diameter of the grub screws is smaller than the core diameter of the thread, allowing them to be screwed in on the pin side. The snap ring resp. snap spring of the thrust pad is a simple and quick method to connect the thrust pad to the grub screw.

  • Volume Discount

  Starting from∗ ：	1.66 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Foot plates

  GANTER

  Foot plates GN 6311.3 are used in connection with screws with pivots (grub screws DIN 6332, tommy screws DIN 6304, DIN 6306).
  
  Owing to the special shape of the immovable retaining ring, the foot plate is easily plugged onto and removed from, the pivot.

  • Volume Discount

  2D / 3D CAD data available

  Starting from∗ ：	13.68 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Stainless Steel-Levelling feet

  GANTER

  [Specifications]
  ・Type: KR. with plastic cap. non-gliding, KS. with plastic cap. gliding, OS. without plastic cap
  ・Foot diameter d1: 50, 60
  
  Stainless steel leveling feet GN 6311.6 are used for installing and leveling devices and equipment. The pin diameter dg is smaller than the core diameter of the thread, with the effect that the screw can be turned in at the pin. The pressure pin is easily inserted into the plate, with the retaining spring ensuring that the assembly is secure in axial direction.

  • Volume Discount

  Starting from∗ ：	20.18 €
  Min. Shipping Days ：	9 Days

  *Unit price with basic configuration

• 

  Thrust pads / Steel / DIN 6311.1

  GANTER

  [Specifications]
  ・Type: A. Thrust pad surface plane. without plastic cap, K. Thrust pad surface plane. with plastic cap, P. Thrust pad surface with detent. without plastic cap
  ・Material: Steel
  
  Thrust pads GN 6311.1 are used in conjunction with grub screws fitted with thrust point (Grub screws DIN 6332, tommy screws DIN 6304 and DIN 6306) to transmit clamping force. They align themselves on uneven and non-parallel surfaces and thus prevent the rotating force being transmitted to the workpiece.

  • Volume Discount

  Starting from∗ ：	4.20 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

• 

  Stainless Steel-Thrust pads

  GANTER

  [Specifications]
  ・Type: A. Thrust pad surface plane. without plastic cap, K. Thrust pad surface plane. with plastic cap, P. Thrust pad surface with detent. without plastic cap
  ・Material: NI. Stainless Steel
  ・Outside diameter d1: 12~40
  
  Thrust pads GN 6311.1 are used in conjunction with grub screws fitted with thrust point (Grub screws DIN 6332, tommy screws DIN 6304 and DIN 6306) to transmit clamping force. They align themselves on uneven and non-parallel surfaces and thus prevent the rotating force being transmitted to the workpiece.

  • Volume Discount

  Starting from∗ ：	5.12 €
  Min. Shipping Days ：	7 Days

  *Unit price with basic configuration

Loading...