STRAIGHT EJECTOR SLEEVES / DIN ISO 8405 / EN 1.2344 Equiv. / Nitrided / ◎0.08 / L, V Dimensions Configurable
Part Number
Once your search is narrowed to one product,
the corresponding part number is displayed here.
- Drawing
- 3D Preview 3D preview is available after complete configuration
- Part Numbers
- Specifications
Drawing / Product specification
| Range of guaranteed shaft diameter precision (b1=L－x1) | |
| x1 max.40 | |
| [ ! ]Nitriding may extend to the head as it is applied after dimension V and D machining. | |
| [ ! ]When the diameter (D) portion of the stepped center pin is inserted into the relief hole (C), make sure | relief hole (C) ≧ pin diameter (D)＋1.0 |
| Type | [ M ] | [ H ] | [ T ] V | Applicable center pin shaft diameter tolerance | |
| D-ESN-L | 1.2344 equivalent+Nitrided | Surface: 900HV Base Material: 40±3HRC | H7 | -0.01 -0.02 | *Note that for sleeves with V dimension tolerance of H7, combination with center pins that have shaft diameter tolerance 0-0.005 is not recommended. The reason for this is the fitting section S are longer. |
| D≦6 | 6.5≦D≦10 | 12≦D≦16 | D＝20 |
| －0.004 －0.012 | －0.005 －0.014 | －0.006 －0.017 | －0.007 －0.020 |
| V≦3.0 | 3.1≦V≦6.0 | 6.1≦V≦10.0 | V≧10.1 |
| +0.010 0 | +0.012 0 | +0.015 0 | +0.018 0 |
Part Number:
- In order to open the 3D preview, the part number must be fixed.
3D preview is not available, because the part number has not yet been determined.
| Part Number | Minimum order quantity | Volume Discount | Head thickness | Shaft diameter tolerance | D/P (Shaft diameter) (mm) | V (Hole diameter) (mm) | L (L dimension) (mm) | C (Recess Diameter) (mm) | S (V Hole Diameter Length) (mm) | |
|---|---|---|---|---|---|---|---|---|---|---|
| 1 | 15 Days | 7mm | -0.006/-0.017 | 12 | 2.5 ～ 10 | 70 ～ 500 | 3 ～ 10.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 12 | 2.5 ～ 10 | 70 ～ 500 | 3 ～ 10.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 12 | 2.5 ～ 10 | 500.1 ～ 800 | 3 ～ 10.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 12 | 2.5 ～ 10 | 500.1 ～ 800 | 3 ～ 10.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 15 | 2.5 ～ 12 | 70 ～ 500 | 3 ～ 12.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 15 | 2.5 ～ 12 | 70 ～ 500 | 3 ～ 12.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 15 | 2.5 ～ 12 | 500.1 ～ 800 | 3 ～ 12.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 15 | 2.5 ～ 12 | 500.1 ～ 800 | 3 ～ 12.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 16 | 3 ～ 13 | 70 ～ 500 | 3.5 ～ 13.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 16 | 3 ～ 13 | 70 ～ 500 | 3.5 ～ 13.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 16 | 3 ～ 13 | 500.1 ～ 800 | 3.5 ～ 13.5 | 20 ～ 100 | ||
| 1 | 15 Days | 7mm | -0.006/-0.017 | 16 | 3 ～ 13 | 500.1 ～ 800 | 3.5 ～ 13.5 | 20 ～ 100 |
Loading...
Specification table
| H | T | Part No. | L | V 0.1mm increments | C 0.1mm increments | Cmax. | S 1mm increments | |||||
| Type | D | 0.01mm increments | 0.1mm increments | |||||||||
| 8 | 3 | D-ESN-L (1.2344 equivalent ＋ Nitrided) | 4 | 40.00～200.00 | - | 1.5～ 2.5 | C≧V＋0.5 ([ ! ]When L>300 0.5mm increments) | 3.0 | 20～100 ([ ! ]D4, D4.5 When V1.5～V1.9 20～40) | |||
| 4.5 | 1.5～ 3.0 | 3.5 | ||||||||||
| 10 | 5 | 40.00～300.00 | 2.0～ 3.5 | 4.0 | ||||||||
| 5.5 | 2.0～ 4.0 | 4.5 | ||||||||||
| 12 | 5 | 6 | 40.00～400.00 | 2.0～ 4.5 | 5.0 | L | (L－S) min. | |||||
| 6.5 | 2.0～ 4.5 | 40.00～60.00 | 20 | |||||||||
| 7 | 2.0～ 5.0 | 5.5 | 60.01～ | 30 | ||||||||
| 7.5 | 2.0～ 5.5 | 6.0 | ||||||||||
| 14 | 8 | 70.00～500.00 | 2.0～ 6.0 | 6.5 | 20～100 (L－S)≧50 | |||||||
| 9 | 2.5～ 7.0 | 7.5 | ||||||||||
| 16 | 10 | 2.5～ 8.0 | 8.5 | |||||||||
| 18 | 7 | 12 | 500.1 ～ 800.0 | 2.5～10.0 | 10.5 | |||||||
| 22 | 15 | 2.5～12.0 | 12.5 | |||||||||
| 16 | 3.0～13.0 | 13.5 | ||||||||||
| 26 | 8 | 20 | 100.00～500.00 | 3.0～16.0 | 16.5 | |||||||
Order Example
| Part No. | - | L | - | V | - | C | - | S | ||
| D-ESN-L6 | - | 300 | - | 3.5 | - | 5.5 | - | S30 | ||
Alteration
| Part No. | - | L | - | V | - | C | - | S | - | (KC・WKC…etc.) | ||
| D-ESN-L8 | - | 500 | - | 4.5 | - | 6.5 | - | S40 | - | KC4.5 | ||
Basic information
| Brand | MISUMI | Product composition | Single sleeve | Material | EN 1.2344 Equiv. |
|---|---|---|---|---|---|
| Surface treatment | Nitrided | Concentricity between the hole and shaft diameters | ◎0.08 | Inner dia. tolerance | H7 |
| Tapered or not | No | Center pin tip shape | No | Technical Standard | DIN |
Configure
Basic Attributes
-
Type
- D-ESN-L
-
Shaft diameter tolerance
- -0.04/-0.012
- -0.005/-0.014
- -0.006/-0.017
- -0.007/-0.020
-
D/P (Shaft diameter)(mm)
-
V (Hole diameter)(mm)
-
L (L dimension)(mm)
-
C (Recess Diameter)(mm)
-
S (V Hole Diameter Length)(mm)
-
Head thickness
- 3mm
- 5mm
- 7mm
- 8mm
-
Filter by CAD data type
- 2D
- 3D
Filter by standard shipping days
-
- All
- 15 Days or Less
Optional Attributes
- The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .
Tech Support
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.