- inCAD Library Home
- > No.000218 Fine Adjustment Mechanism Using Flat Springs
No.000218 Fine Adjustment Mechanism Using Flat Springs
15
15
Slide Adjustment Utilizing Flat Spring
Related Category
Adjusting Stopper Screws
| Product name | Adjusting Stopper Screws/Hexagon Socket/L Configurable/Fine Thread |
|---|---|
| Part number | ANBS6-20 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Screw with radius at the end is suitable for holding the flat spring.
Available sizes
■Adjusting Stopper Screws - Hex Socket Type
| Adjusting | Material | Hardness | Surface Treatment |
|---|---|---|---|
| Fine Thread | EN 1.1191 Equiv. | 45-50HRC | Electroless Nickel Plating |
| Trivalent Chromate | |||
| EN 1.7220 Equiv. | 50HRC- | ||
| EN 1.4301 Equiv. | - | - | |
| EN 1.4031 Equiv. | 45HRC- | - | |
| Coarse Thread | EN 1.1191 Equiv. | 45-50HRC | Electroless Nickel Plating |
| Trivalent Chromate | |||
| EN 1.7220 Equiv. | 50HRC- | ||
| EN 1.4301 Equiv. | - | - | |
| EN 1.4031 Equiv. | 45HRC- | - |
■Sizes and Dimensions
| Screw Shaft Dia. (mm) | Thread Length | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 10 | 15 | 20 | 25 | 30 | 35 | 40 | 45 | 50 | 60 | 70 | 80 | 90 | 100 | 120 | |
| 3 | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - | - | - | - | - | - |
| 4 | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - | - | - |
| 5 | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - | - | - |
| 6 | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - | - | - |
| 8 | - | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - | - | - |
| 10 | - | - | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - | - |
| 12 | - | - | - | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | - | - | - |
| 16 | - | - | - | - | - | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ |
| 20 | - | - | - | - | - | - | - | ○ | ○ | ○ | ○ | ○ | ○ | ○ | ○ |
Strut Clamp, Unequal Dia., Parallel Holes, Pitch Selectable
| Product name | Parallel Configuration/Different Diameter/Selectable Pitch |
|---|---|
| Part number | KKQT20-15-40 |
| Features | For parallel shaft configuration. |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Effective for connecting two parallel shafts.
Available sizes
■Strut Clamp (Unequal Dia., Parallel Holes, Pitch Selectable)
| Material | Surface Treatment | Accessory |
|---|---|---|
| EN 1.0038 Equiv. | Black Oxide | Hex Socket Head Cap Screw |
■Sizes and Dimensions
| Large Hole Dia. | Small Hole Dia. | Hole Pitch | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|
| 15 | 20 | 25 | 30 | 40 | 50 | 75 | 100 | 150 | ||
| 10 | 8 | ○ | ○ | ○ | - | - | - | - | - | - |
| 12 | 10 | ○ | ○ | ○ | ○ | - | - | - | - | - |
| 15 | ○ | ○ | ○ | ○ | - | - | - | - | - | |
| 20 | 15 | - | ○ | ○ | ○ | ○ | - | - | - | - |
| 25 | - | - | ○ | ○ | ○ | ○ | - | - | - | |
| 30 | 20 | - | - | - | ○ | ○ | ○ | ○ | - | - |
| 35 | 25 | - | - | - | - | - | ○ | ○ | ○ | ○ |
Accuracy Info
■Accuracy of Strut Clamp
| Large Hole Dia. | Large Hole Dia. Tolerance (H7) | Small Hole Dia. | Small Hole Dia. Tolerance (H7) |
|---|---|---|---|
| 10 | +0.015 0 | 8 | +0.015 0 |
| 12 | +0.018 0 | 10 | |
| 15 | |||
| 20 | +0.021 0 | 15 | +0.018 0 |
| 25 | |||
| 30 | 20 | +0.021 0 | |
| 35 | +0.025 0 | 25 |
Parallelism of Holes: 0.05
-
TERMS AND CONDITIONS FOR USE OF CAD DATA-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
- 1. CAD Data
- The Data is prepared for assisting the Company's users in the CAD design process by providing dimensions and other Product information. In order to provide the best speed and stability working within this site, the Product drawings were simplified to reduce the size of the Data. For instance, some of the Products are shown without the oil groove shape, screws or spring shape. Also, please be aware that the tolerance, surface roughness and/or chamfer of the Data may vary from the actual Products.
- 2. Disclaimer on Data
- While the Company has carefully prepared the Data, accuracy of the Data is not guaranteed and is subject to the variances as described above. The Company may also modify, add or delete the Data at any time without prior notice. The Company assumes no liability for any direct, indirect, consequential or special damages that you may claim resulted from your use of the Data or any changes to or deletions of the Data regardless of the reason. The Company provides no warranty as to the quality, accuracy, functionality, safety or reliability of the combination of Products and parts. Example applications and combinations of the Products are provided for illustrative purposes only.
- 3. Copyright
-
Copyrights to the content and the Data belong to the Company or the manufacturers of the Products. The said copyright is protected by the Copyright Act and international treaties. The use (including duplication, modification, uploading, posting, transmission, distribution, licensing, sales and publishing) of the Data except for the purpose to use the Data described above without prior approval of the Company is not allowed. The Data cannot be used for any purposes (including sales promotion) except for designing your machine. If you violate this provision or the laws or regulations, the Company may prohibit you from the use of the Data, the Company’s site and/or take legal action. So long as you comply with these terms and conditions, the Company grants to you a non-exclusive, non-transferable, revocable license to access and use the Data for the sole purpose of assisting you in designing machines that incorporate products.
- 4. Disclaimer of Warranty
- ANY AND ALL CONTENT APPEARING ON THIS WEB SITE IS PROVIDED FOR INFORMATIONAL PURPOSES ONLY. THIS WEB SITE, ITS CONTENT AND ITS LINKS ARE PROVIDED ON AN "AS IS" AND "AS AVAILABLE" BASIS AND ARE USED ONLY AT YOUR SOLE RISK, TO THE FULLEST EXTENT PERMISSIBLE BY LAW. THE COMPANY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND, REGARDING THIS WEB SITE (INCLUDING ITS CONTENT, HARDWARE, SOFTWARE AND LINKS), INCLUDING AS TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, TITLE, NON INFRINGEMENT, RESULTS, ACCURACY, COMPLETENESS, ACCESSIBILITY, COMPATIBILITY, SECURITY AND FREEDOM FROM COMPUTER VIRUS. THE COMPANY WILL NOT BE LIABLE FOR ANY DAMAGES OR LOSSES, INCLUDING DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL OR PUNITIVE DAMAGES AND/OR LOST PROFITS, IN CONNECTION WITH USE OF THE INTERNET, THIS WEB SITE, ITS CONTENT OR ITS LINKS
Further, the Company will not be liable to you for any failure or delay by the Company to provide access to the Data or any of its obligations under these terms and conditions where such failure or delay is the direct or indirect result of any circumstances beyond the Company's reasonable control (and the Company's obligations will be suspended for the duration of such circumstances). - 5. Policy of Third Parties
- You may be required to separately agree to third party's policies if you use third party software to create or browse the Data or use a third party’s CAD data. In this case, the Company does not assume any responsibility for defects of such CAD data or the software of the third party or violation of their rights. Understand them before use.
CAD Data Download (Unit Assembly)
CAD Data Download: File Format
Cautions on the CAD data
-
Assembly data shows the assembly drawings in the concept design phase. The sole purpose of the data is to explain the structure and functionality of the assembly and is not considered nor to be used as a final design.
You will need to edit the Data so that it meets your specific design conditions. -
The CAD data unit assembly consists of sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited. - The Data for fabricated parts is based on easy-to-edit dimensions and shapes in sketches and histories.
- The Data including the third-part components are made by the Company.
* The part in the frame is a sub-assembly unit.
-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
-
- * Unit assembly CAD data consists of some sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited.
Application Overview
Purpose
- Purpose
- To perform fine adjustment during product inspection without changing overall dimensions and layout of the fixture.
- Operation
- By pressing the flat springs, which are installed at both ends of the slide shaft, from the outside using adjusting bolts, the slide shaft moves. Due to this movement, the optical axis of the inspection camera that is mounted onto strut clamp is adjusted.
After that, lock the position of the slide shaft by applying the adjusting screws to the flat springs from opposite direction.
- By pressing the flat springs, which are installed at both ends of the slide shaft, from the outside using adjusting bolts, the slide shaft moves. Due to this movement, the optical axis of the inspection camera that is mounted onto strut clamp is adjusted.
Target workpiece
- Shape: mounted circuit board
- Size: W80 x D80 x H12mm
- Weight: 40g
Design Specifications
Operating Conditions or Design Requirements
- Maximum fine adjustment amount: 1.6mm
- Outer dimensions: W100 x D242 x H53mm
Selection Criteria for Main Components
- Select adjustment screws that can be used when the flat spring deflection is 1.6mm.
Design Evaluation
Verification of main components
- Verify that length of the adjusting bolts are sufficient to support all camera positions.
- Selection of stopper bolts
- Conditional value: arc length of flat spring (EN 1.4301 Equiv.) L1 = 49.5mm, spring deflection limit σ = 275N/mm², Young's modulus of flat spring E = 186000N/mm², thickness of flat spring H = 1.0mm, arc length from flat spring fixing side to adjusting screw L2 = 24.75mm, length from flat spring to plate for adjusting screw L3 = 11.1mm, overall length of adjusting screw L4 = 30mm, height of nut supplied with adjusting screw L5 = 4mm
- If we assume that the arc-shaped flat spring is a straight line, the deflection σ2 when it is handled as a spring with one end fixed,
σ2 = σ x L2² x (3 x L1/L2 - 1)/(3 x E x H) = 275 x 24.75² x (3 x 49.5/24.75 - 1)/(3 x 186000 x 1.0) = 1.51mm
⇒The length of adjusting screw that can perform adjustment even when the flat spring deflects for 1.51mm is
range satisfying 1.51 + L3 < L4 - L5
1.51 + 11.1 < 30 - 5.4
⇒30mm, hence, selected adjusting stopper screw is acceptable for this application.
Other Design Consideration
- When a flat spring is being adjusted using an adjusting screw on one end, the adjusting screw on the other end should not be in contact with the flat spring.
Explore Similar Application Examples
Page
-
/
-
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.