Keyless Bushing (Fastening Fittings)（Page 3）

?* Information on days to ship and prices

• 

  Taper Bushes 2012

  MAEDLER

  Material: GG25.
  Bores ISO E8. Metric bores with feather keyways DIN 6885/1. Inch bores with feather keyways like British Standard (BS).
  Screws included in delivery. Thread BSW. Cone and front side ground.
  Shaft tolerance +0.05/-0.125 mm. Can be used with or without parallel key, depending on the required torque.
  Other bush sizes and bores available at short notice.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	10.94 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Taper Bushes 3535

  MAEDLER

  Material: GG25.
  Bores ISO E8. Metric bores with feather keyways DIN 6885/1. Inch bores with feather keyways like British Standard (BS).
  Screws included in delivery. With three screws. Thread BSW. Cone and front side ground.
  Shaft tolerance +0.05/-0.125 mm. Can be used with or without parallel key, depending on the required torque.
  Other bush sizes and bores available at short notice.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	49.79 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Shrink Disks ST

  MAEDLER

  Material: High-quality steel.
  • For very high torques.
  • No axial shaft-hub movement.
  • Quick mounting.
  • Quick demounting.
  • Not self-centering.
  • Concentricity 0.02-0.04 mm.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	18.99 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Miniature Clamping Bushes MSM-N

  MAEDLER

  Material: Version MSM-N: Stainless steel 1.4305 (AISI 303).
  Concentricity: about 0.02 mm.
  Tolerance: Shaft k6-h10, Hub H8.
  
  P_W ≈ 90N/mm², P_N ≈ 70N/mm²

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	46.62 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Locking Assemblies TT 3-16 mm

  MAEDLER

  Material: Steel.
  • For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft.
  • For high torques.
  • Self-centering.
  • Axial offset during mounting (can be compensated by correct positioning).

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	31.75 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Locking Assemblies TT 17-35 mm

  MAEDLER

  Material: Steel.
  • For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft.
  • For high torques.
  • Self-centering.
  • Axial offset during mounting (can be compensated by correct positioning).

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	39.57 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Locking Assemblies TOK Version A

  MAEDLER

  Material Version A: Steel, bright.
  • For fixing a hub (e.g. drive wheel, rotor or similar) on a shaft.
  • For medium torques.
  • Self-centering.
  • Axial offset during mounting (can be compensated by correct positioning).

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	12.35 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Locking Assemblies (Rigid Couplings) ST-K

  MAEDLER

  Material: Steel.
  • For connecting two shafts, as a rigid coupling.
  • For medium torques.
  • Easy mounting.
  • Self-releasing at dismounting.
  • No axial movement during mounting.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	19.59 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Clamping Bushes E

  MAEDLER

  Material: High-quality steel.
  The clamping bush consists of a double-walled steel sleeve filledwith a pressure medium, and a flange part. Inside the flange thereis a screw and a piston with seal to build up compression.
  Function: When the thrust screw is tightened, the sleeve expandsuniformly against shaft and hub, creating a rigid connectionthrough frictional force. When the thrust screw is loosened, thebush returns to its initial position and can be easily disassembled.
  Concentricity: 0.02 mm.
  Tolerances: Shaft h7 for d = 15 mm.
  Shaft k6-h7 for d = 19, 22, 24, 28 and 38 mm.
  Shaft h8 for the other diameters d.
  Hub H7.
  Temperature range: -30°C to 85°C.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	247.10 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• 

  Shrink disc, stainless steel (23380)

  NORELEM

  · To connect a hollow shaft to a shaft
  
  · Suitable for static, dynamic and shock loads
  
  · For very high torques
  
  · No shift of axial shaft/hub during assembly
  
  · Self-centring

  Select to compare

  Configure now
  Starting from∗ ：	99.62 €
  Min. Shipping Days ：	4 Days

  *Unit price with basic configuration

• • Promotional pricing ends 31/12/2024

  

  Mecha-Lock MKA, Rust-Proof Standard Electroless Nickel Plating Specifications

  ISEL

  Centering function suppresses outer circumference and terminal surface run-out. Electroless nickel plated product.

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	56.59 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 31/12/2024

  

  Mecha-Lock MT, General Purpose Type

  ISEL

  No drag when connecting for easy removal

  • Volume Discount

  2D / 3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	35.76 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• • Promotional pricing ends 31/12/2024

  

  Keyless Bushing, Self-Aligning Type SDS

  Save & Secure

  Self-centering type of keyless bushing. Abundant variations to choose from, with allowable torque from 6.2 to 13000N·m. The SS company manufactures a 20% share of the couplings in Taiwan. The company's are centered on China and Southeast Asia, and is trying to expand both its domestic and foreign shares.

  • Volume Discount

  3D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	24.33 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Keyless Bushing, Straight Type

  CAP

  Brand-name products provided by MISUMI-VONA are offered based on customers' needs that selected from products of Asian manufacturers carefully. Please select an item according to the user's various usage scenes. CAPT This company is developing domestic and foreign high-quality and inexpensive keyless bushing and sprockets. We are adopting not only more Chinese but also Japanese manufacturers.

  2D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	14.80 €
  Min. Shipping Days ：	58 Days

  *Unit price with basic configuration

• 

  Keyless Bushing A.P.LOCK SAPL-AK Series

  SUNGIL

  [Features]
  · Self-centering function: Prevents minute Off-centering.
  · Difference between internal diameter (d) and outer diameter (D) is slight, and can also be installed to small hubs with light pressure on its surface.
  · Internal diameters 4.5ø to 40ø standardized.
  · Has simple structure for easy assembly.
  · Choose from stainless steel (vacuum environments) or electroless nickel plated products (corrosion proof) to suit the use environment

  2D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	24.96 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

• 

  Keyless Bushing A.P.LOCK SAPL-AS Series

  SUNGIL

  [Features]
  · Self-centering function: Prevents minute Off-centering.
  · Difference between internal diameter (d) and outer diameter (D) is slight, and can also be installed to small hubs with light pressure on its surface.
  · Internal diameters 4.5ø to 40ø standardized.
  · Has simple structure for easy assembly.
  · Choose from stainless steel (vacuum environments) or electroless nickel plated products (corrosion proof) to suit the use environment

  2D CAD data available

  Select to compare

  Configure now
  Starting from∗ ：	67.20 €
  Min. Shipping Days ：	10 Days

  *Unit price with basic configuration

• • Promotional pricing ends 31/12/2024

  

  SP Bushing

  EVER-ON CORPORATION

  [Features]
  ● Shaft hole machining and QA machining not required.
  ● Conforms to new JIS key specifications.
  
  [Applications]
  ● For connecting shafts to their appropriate pulleys.

  • Volume Discount

  Select to compare

  Configure now
  Starting from∗ ：	32.67 €
  	Special price
  Min. Shipping Days ：	Same day

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 1108 with Inch Drill

  CONCAR

  [Specifications]
  ・Type: 1108
  ・Body Material: Cast Iron
  ・Standard: British Standard BS 46 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	10.91 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 1108 with Metric Drill

  CONCAR

  [Specifications]
  ・Type: 1108
  ・Body Material: Cast Iron
  ・Standard: DIN 6885 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	3.38 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 1210 with Inch Drill

  CONCAR

  [Specifications]
  ・Type: 1210
  ・Body Material: Cast Iron
  ・Standard: British Standard BS 46 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	14.54 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 1215 with Metric Drill

  CONCAR

  [Specifications]
  ・Standard: DIN 6885 Part 1
  
  Tapered Clamping Bush 1215 with Metric Drill

  Select to compare

  Configure now
  Starting from∗ ：	5.51 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 1310 with Metric Drill

  CONCAR

  [Specifications]
  ・Type: 1310
  ・Body Material: Cast Iron
  ・Standard: DIN 6885 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	9.08 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 1610 with Inch Drill

  CONCAR

  [Specifications]
  ・Type: 1610
  ・Body Material: Cast Iron
  ・Standard: British Standard BS 46 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	17.45 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 1615 with Inch Drill

  CONCAR

  [Specifications]
  ・Type: 1615
  ・Body Material: Cast Iron
  ・Standard: British Standard BS 46 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	18.17 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 1615 with Metric Drill

  CONCAR

  [Specifications]
  ・Type: 1615
  ・Body Material: Cast Iron
  ・Standard: DIN 6885 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	9.08 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 2012 with Inch Drill

  CONCAR

  [Specifications]
  ・Type: 2012
  ・Body Material: Cast Iron
  ・Standard: British Standard BS 46 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	21.45 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 2517 with Metric Drill

  CONCAR

  [Specifications]
  ・Type: 2517
  ・Body Material: Cast Iron
  ・Standard: DIN 6885 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	8.18 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 3020 with Inch Drill

  CONCAR

  [Specifications]
  ・Type: 3020
  ・Body Material: Cast Iron
  ・Standard: British Standard BS 46 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	34.54 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 3020 with Metric Drill

  CONCAR

  [Specifications]
  ・Type: 3020
  ・Body Material: Cast Iron
  ・Standard: DIN 6885 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	18.54 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 3030 with Inch Drill

  CONCAR

  [Specifications]
  ・Type: 3030
  ・Body Material: Cast Iron
  ・Bore diameter(mm): 76.2
  ・Standard: British Standard BS 46 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	92.34 €
  Min. Shipping Days ：	17 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 3030 with Metric Drill

  CONCAR

  [Specifications]
  ・Type: 3030
  ・Body Material: Cast Iron
  ・Standard: DIN 6885 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	25.80 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 3535 with Inch Drill

  CONCAR

  [Specifications]
  ・Type: 3535
  ・Body Material: Cast Iron
  ・Standard: British Standard BS 46 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	87.25 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 3535 with Metric Drill

  CONCAR

  [Specifications]
  ・Type: 3535
  ・Body Material: Cast Iron
  ・Standard: DIN 6885 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	43.62 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Tapered Clamping Bush 4040 with Metric Drill

  CONCAR

  [Specifications]
  ・Type: 4040
  ・Body Material: Cast Iron
  ・Standard: DIN 6885 Part 1
  
  Taper bushes are used to affix pulleys or couplings to shafts. Each taper bush is fitted with a feather keyway in case higher loads occur during the power transfer. ConCar has these bushes in its product range, with metric and imperial bores.

  Select to compare

  Configure now
  Starting from∗ ：	61.43 €
  Min. Shipping Days ：	3 Days

  *Unit price with basic configuration

• 

  Locking Assemblies 7004

  RINGFEDER

  Universal clamping set for a wide range of applications. Self centering and mounting friendly at medium to high torques.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  Locking Assemblies 7007

  RINGFEDER

  Universal clamping set for a wide range of applications. Self centering and mounting friendly at medium to high torques. No axial displacement through stop ring.

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  Locking Assemblies 7014

  RINGFEDER

  Clamping set for very high torques. The design allows maximum torques and axial forces to be transmitted with a clamping set.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  Locking Assemblies 7075

  RINGFEDER

  Clamping set made of steel with central nut. Ideal for small components, tight installation space. The construction by the central clamping nut makes this clamping set very easy to install and has excellent concentricity and concentricity.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  Locking Assemblies 7085

  RINGFEDER

  Clamping set made of steel with central nut. Ideal for small components, tight installation space. The construction by the central clamping nut makes this clamping set very easy to install and has excellent concentricity and concentricity. The clamping set is additionally nickel-plated.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  Locking Assemblies 7110

  RINGFEDER

  Clamping set for hubs with low wall thickness. Ideal for aluminum hubs.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  Locking Assemblies 8006 SST

  RINGFEDER

  Ideally adaptable clamping element made of stainless steel for large transmission forces in a small space. Absolutely backlash-free, wear-free and maintenance-free.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	3 Days

• 

  Locking Assemblies Stainless Steel 7013.1 SST

  RINGFEDER

  Stainless steel clamping set with excellent concentricity and very good disassembly - with these self-centering clamping sets a particularly good concentricity between the clamped parts is achieved. The flange is reinforced at the critical point, this prevents bending and lifting of the inner ring during assembly. This ensures good demountability. Ideal for high speeds, radial loads and for axial hub fixation. High-strength clamping screws allow a higher performance range.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  Locking Assemblies Stainless Steel 7090

  RINGFEDER

  Stainless clamping set with central nut. Ideal for small components, tight installation space. The construction by the central clamping nut makes this clamping set very easy to install and has an excellent concentricity and concentricity.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  Shrink Disc Stainless Steel 4061 SST

  RINGFEDER

  Shrink disc made of stainless steel for high torques. Compensation of smaller tolerances possible with simple assembly and disassembly. Due to special high-strength materials with increased performance range.

  3D CAD data available

  Select to compare

  Configure now
  Min. Shipping Days ：	5 Days

• 

  OPTIBELT Taper Bushing with Metric Bore

  OPTIBELT

  [Specifications]
  ・Shaft Bore Dia. d(Ø): 14-100
  ・Allowable Torque(N•m): 5.7-195
  ・Overall Length W(mm): 22.3-114.3
  ・Keyway: DIN 6885 Part 1, Shallow key
  ・Engineering material: 0.6020 (EN-GJL 200)

  Select to compare

  Configure now
  Starting from∗ ：	4.78 €
  Min. Shipping Days ：	5 Days

  *Unit price with basic configuration

Loading...