- inCAD Library Home
- > No.000075 Rotate and Transfer Mechanism
No.000075 Rotate and Transfer Mechanism
58
58
Motor and gear system rotates the arm and gripper simultaneously.
Related Category
Spur Gears
| Product name | Spur Gears/Induction Hardened/Pressure Angle 20Deg. |
|---|---|
| Part number | GEAHBH2.0-36-20-A-35 |
| Features | Gears with hardened teeth which provides excellent strength, abrasion resistance and high precision |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
A gear is placed to reduce the speed of the motor output rotation by half
Available sizes
■Induction Hardened Spur Gears (Ground)
| Material | Surface Treatment | Hardness | Accessory |
|---|---|---|---|
| EN 1.1191 Equiv. | Black Oxide | Tooth Induction Hardened 51 - 55 HRC (depth 1 mm or more) | Set screw (EN 1.7220 Equiv. Black Oxide) |
■Sizes and Dimensions
| Module | Number of Teeth | Shaft bore DIA. (1 mm Increments) | |
|---|---|---|---|
| Round Hole Round Hole + Tap | Keyway Keyway + Tap | ||
| 2.0 | 15 | 12 - 17 | 12 - 14 |
| 16 | 12 - 18 | 12 - 15 | |
| 18 | 12 - 21 | 12 - 18 | |
| 20 | 15 - 22 | 15 - 19 | |
| 22 | |||
| 24 | 15 - 26 | 15 - 23 | |
| 25 | 15 - 28 | 15 - 24 | |
| 28 | 15 - 31 | 15 - 28 | |
| 30 | 18 - 35 | 18 - 31 | |
| 32 | |||
| 36 | |||
| 40 | 20 - 42 | 20 - 38 | |
| 45 | |||
| 48 | |||
| 50 | 25 - 42 | 25 - 38 | |
| 60 | 25 - 45 | 25 - 42 | |
| 2.5 | 16 | 15 - 22 | 15 - 19 |
| 20 | 18 - 28 | 18 - 24 | |
| 24 | 18 - 33 | 18 - 30 | |
| 25 | 20 - 35 | 20 - 31 | |
| 28 | 20 - 42 | 20 - 38 | |
| 30 | 20 - 45 | 20 - 42 | |
| 36 | 20 - 49 | 20 - 45 | |
| 40 | 25 - 49 | 25 - 45 | |
| 45 | 25 - 52 | 25 - 49 | |
| 48 | |||
| 50 | 25 - 56 | 25 - 50 | |
Accuracy Info
■Accuracy of Induction Hardened Spur Gears (Ground)
Gear accuracy: Previous JIS B 1702 Class 2 (New JIS B 1702-1 Class 6 equivalent)
Shaft bore DIA. tolerance: H7
Rod End Bearings
| Product name | Rod End Bearings/90 Deg. Link Ball Type |
|---|---|
| Part number | RBLD5 |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
Connecting link mechanism.
Available sizes
■Rod End Bearings (Link Ball L Type / Right hand thread)
| Material | |
|---|---|
| Holder | High Strength Zinc Alloy * M4, 5: High Strength Aluminum Alloy |
| Shank with Ball | EN 1.1181 Equiv. |
| Boots | NBR Type Special Synthetic Rubber |
■Sizes and Dimensions
| Thread Dia. | Ball Center - Holder Edge | Ball Center - Shank Edge |
|---|---|---|
| 4 | 18 | 15 |
| 5 | 27 | 21 |
| 6 | 30 | 26 |
| 8 | 36 | 31 |
| 10 | 43 | 43 |
| 10 (Fine Thread) | 37 | |
| 12 | 50 | 49 |
| 12 (Fine Thread) | 42 | |
| 14 | 57 | 62 |
| 14 (Fine Thread) | 56 | |
| 16 | 64 | 66 |
| 16 (Fine Thread) | 60 |
Accuracy Info.
■Allowable Incline Angle of Rod End Bearings
| Thread Dia. | Allowable Incline Angle |
|---|---|
| 4 | 40° |
| 5 | |
| 6 | |
| 8 | |
| 10 | |
| 10 (Fine Thread) | |
| 12 | |
| 12 (Fine Thread) | |
| 14 | |
| 14 (Fine Thread) | |
| 16 | 30° |
| 16 (Fine Thread) |
Performance info.
■Yield Strength and Static Load Capacity of Rod End Bearings
| Thread Dia. | Yield Strength (N) | Static Load Capacity (N) |
|---|---|---|
| 4 | 1370 | 4510 |
| 5 | 2250 | 6470 |
| 6 | 3920 | 9900 |
| 8 | 6570 | 12500 |
| 10 | 11300 | 18300 |
| 10 (Fine Thread) | ||
| 12 | 16400 | 26700 |
| 12 (Fine Thread) | ||
| 14 | 19800 | 36400 |
| 14 (Fine Thread) | ||
| 16 | 26900 | |
| 16 (Fine Thread) |
Rod End Coupling Rods
| Product name | Rod End Coupling Rods/Both Ends Threaded |
|---|---|
| Part number | LBRFN5-180 |
| Features | Rod End Coupling Rods with the right-hand/left-hand thread selectable in size and length. |
* Orange colored cells in the table below indicate the part numbers used in this example.
Selection criteria
To connect rod end bearings.
Available sizes
■Rod End Coupling Rods (Both Ends Threaded, Length Configurable)
| Material | Surface Treatment | Accessory (one hex nut for right / left-hand thread) | |
|---|---|---|---|
| Material | Surface Treatment | ||
| EN 1.1191 Equiv. | Black Oxide | EN 1.1191 Equiv. | Trivalent Chromate |
| Electroless Nickel Plating | |||
| EN 1.4301 Equiv. | - | EN 1.4301 Equiv. | - |
■Sizes and Dimensions
| Thread Dia. (Coarse) | Overall Length | Thread Length (Under Head) | Opposite Side |
|---|---|---|---|
| 3 | 25 - 39 | 8 | 6 |
| 40 - 300 | 15 | ||
| 4 | 35 - 49 | 12 | 7 |
| 50 - 400 | 20 | ||
| 5 | 40 - 59 | 13 | 8 |
| 60 - 600 | 25 | ||
| 6 | 50 - 69 | 17 | 10 |
| 70 - 600 | 30 | ||
| 8 | 60 - 89 | 23 | 13 |
| 90 - 1000 | 40 | ||
| 10 | 70 - 109 | 28 | 17 |
| 110 - 1000 | 50 | ||
| 12 | 80 - 129 | 33 | 19 |
| 130 - 1000 | 60 | ||
| 14 | 130 - 1000 | 60 | 21 |
| 16 | 170 - 1000 | 80 | 24 |
| 18 | 170 - 1000 | 80 | 27 |
| 20 | 170 - 1000 | 80 | 30 |
| 22 | 170 - 1000 | 80 | 32 |
-
-
TERMS AND CONDITIONS FOR USE OF CAD DATA-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
- 1. CAD Data
- The Data is prepared for assisting the Company's users in the CAD design process by providing dimensions and other Product information. In order to provide the best speed and stability working within this site, the Product drawings were simplified to reduce the size of the Data. For instance, some of the Products are shown without the oil groove shape, screws or spring shape. Also, please be aware that the tolerance, surface roughness and/or chamfer of the Data may vary from the actual Products.
- 2. Disclaimer on Data
- While the Company has carefully prepared the Data, accuracy of the Data is not guaranteed and is subject to the variances as described above. The Company may also modify, add or delete the Data at any time without prior notice. The Company assumes no liability for any direct, indirect, consequential or special damages that you may claim resulted from your use of the Data or any changes to or deletions of the Data regardless of the reason. The Company provides no warranty as to the quality, accuracy, functionality, safety or reliability of the combination of Products and parts. Example applications and combinations of the Products are provided for illustrative purposes only.
- 3. Copyright
-
Copyrights to the content and the Data belong to the Company or the manufacturers of the Products. The said copyright is protected by the Copyright Act and international treaties. The use (including duplication, modification, uploading, posting, transmission, distribution, licensing, sales and publishing) of the Data except for the purpose to use the Data described above without prior approval of the Company is not allowed. The Data cannot be used for any purposes (including sales promotion) except for designing your machine. If you violate this provision or the laws or regulations, the Company may prohibit you from the use of the Data, the Company’s site and/or take legal action. So long as you comply with these terms and conditions, the Company grants to you a non-exclusive, non-transferable, revocable license to access and use the Data for the sole purpose of assisting you in designing machines that incorporate products.
- 4. Disclaimer of Warranty
- ANY AND ALL CONTENT APPEARING ON THIS WEB SITE IS PROVIDED FOR INFORMATIONAL PURPOSES ONLY. THIS WEB SITE, ITS CONTENT AND ITS LINKS ARE PROVIDED ON AN "AS IS" AND "AS AVAILABLE" BASIS AND ARE USED ONLY AT YOUR SOLE RISK, TO THE FULLEST EXTENT PERMISSIBLE BY LAW. THE COMPANY DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, OF ANY KIND, REGARDING THIS WEB SITE (INCLUDING ITS CONTENT, HARDWARE, SOFTWARE AND LINKS), INCLUDING AS TO FITNESS FOR A PARTICULAR PURPOSE, MERCHANTABILITY, TITLE, NON INFRINGEMENT, RESULTS, ACCURACY, COMPLETENESS, ACCESSIBILITY, COMPATIBILITY, SECURITY AND FREEDOM FROM COMPUTER VIRUS. THE COMPANY WILL NOT BE LIABLE FOR ANY DAMAGES OR LOSSES, INCLUDING DIRECT, INDIRECT, CONSEQUENTIAL, SPECIAL, INCIDENTAL OR PUNITIVE DAMAGES AND/OR LOST PROFITS, IN CONNECTION WITH USE OF THE INTERNET, THIS WEB SITE, ITS CONTENT OR ITS LINKS
Further, the Company will not be liable to you for any failure or delay by the Company to provide access to the Data or any of its obligations under these terms and conditions where such failure or delay is the direct or indirect result of any circumstances beyond the Company's reasonable control (and the Company's obligations will be suspended for the duration of such circumstances). - 5. Policy of Third Parties
- You may be required to separately agree to third party's policies if you use third party software to create or browse the Data or use a third party’s CAD data. In this case, the Company does not assume any responsibility for defects of such CAD data or the software of the third party or violation of their rights. Understand them before use.
CAD Data Download (Unit Assembly)
CAD Data Download: File Format
Cautions on the CAD data
-
Assembly data shows the assembly drawings in the concept design phase. The sole purpose of the data is to explain the structure and functionality of the assembly and is not considered nor to be used as a final design.
You will need to edit the Data so that it meets your specific design conditions. -
The CAD data unit assembly consists of sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited. - The Data for fabricated parts is based on easy-to-edit dimensions and shapes in sketches and histories.
- The Data including the third-part components are made by the Company.
* The part in the frame is a sub-assembly unit.
-
Your access to the CAD data that MISUMI Corporation (hereinafter referred to as the Company) posts on this site (including 3D CAD data, intermediate 3D CAD data and 2D CAD data; hereinafter referred to as the Data) are of products manufactured and/or sold by the Company (hereinafter referred to as the Products) assumes that you have read and accepted these terms and conditions which govern your use of the Data. If you do not agree to these terms and conditions, you must stop using this website and the Data. You must not use the Data for any unlawful purpose or in any manner inconsistent with these terms and conditions.
-
- * Unit assembly CAD data consists of some sub-assemblies.
Each sub-assembly unit can be used as it is or can be edited.
Application Overview
Purpose
- Transfers workpieces on a conveyor to the next process by rotating the work piece 180°. The arm rotates the workpiece 90°and the linkage rotates the gripper another 90°.
- Gripper down→Retain workpiece→Gripper up→ 90°rotate & transfer ･ Workpiece rotate 90°→Gripper down→Workpiece released→Gripper up.
Target workpiece
- Shape: Connector
Size: W50 x D10 x H15mm
Weight: 0.1kg
Design Specifications
Operating Conditions or Design Requirements
- Transfer angle: 90 degrees
- Workpiece rotation angle: 90 degrees
- Cylinder stroke: 20mm
- Clamp stroke: 10mm
- External dims: W100 x D317 x H269 (Before rotation)
Selection Criteria for Main Components
- Ratio of fixed linkage and moving linkage ratio to be 1:1.
- Suppress inertia by reducing weight of swinging components.
- Confirm that the gear is strong enough to withstand the inertial force.
- Select the air gripper based on friction coefficient and workpiece weight.
Design Evaluation
Verification of main components
- It is important to calculate the inertia that applies to the stepper motor. The calculations are below.
- Time that takes to move 90° t 1 : 0.5sec
- Acceleration time t0 : 0.1sec
- Swinging and rotating arm inertia moment: J 1 = 4.063 x 10⁻² kg･m²
- Inertia moment of a gear on the motor shaft: J 2 = 3.598 x 10⁻⁵ kg･m²
- Inertia moment applicable to motor shaft: Since it is via gear, JL = J 1 x (Number of Teeth of sm. gear / Number of Teeth of L. gear)² +J 2 = 1.019 x 10⁻² kg･m²
- Operating pulses:A = θ/θs = 1250pulses
Here, the operating angle:θ = 90°, Min. step angle of stepping motor:θs = 0.072° - Operational pulse rate: f2 = A / (t 0 - t 1 ) = 3125Hz
- Motion speed: NM = θs/360 x f 2 x 60 = 37.5r/min
- Inertia moment of motor's rotor: J = 0 =2.8 x 10⁻⁵
- Motor gear ratio: i = 10
- Acceleration torque calculation: Ta = (J 0 ･i² +JL) / 9.55 x NM / t 1 = 0.51N･m
- Calculation of required torque:TM = Ta x Safety margin = 1.02N･m Safety ratio given: 2) Select motor from torque characteristics chart.Motor is OK
- Verifying inertia ratio: JL / (J 0 x i²) = 3.64≤10 is OK
Other Design Consideration
- The main shaft (center of rotation) and linkage arm to the main shaft are fixed.
- The gripper at rotation end can elevate and rotate.
Explore Similar Application Examples
Page
-
/
-
Payment Method
On-Demand Manufacturing
Certificates
Copyright © MISUMI Corporation All Rights Reserved.